Home
Research
Team
Courses
Publications

 

Last modified on 02-11-2009

 

          Publications

            In SCI Journals

Alkoy, E. M., Papila, M., "The Effect of CuO Sintering Aid on the Microstructural Features and Electrical Properties of Potassium Sodium Niobate Ceramics and Fibers,  submitted to Journal of American Ceramic Society, August 2009.

 

Dagdeviren, C., Okutan, M., San, S. E., Papila, M., "The Effect of Processing and Crystallinity upon Dielectric Behavior of PVDF,  submitted to Journal of Applied Polymer Science, June 2009.

 

J13. Cilingir, D., Papila, M., "Equivalent electromechanical coefficient for IPMC actuator design based on equivalent bimorph beam theory,  Experimental Mechanics, accepted October 2009.

 

J12. Alkoy, E. M., Dagdeviren, C., Papila, M., "Investigation of the processing conditions and aging effect on the properties of PZT nanofibers obtained by electrospinning processJournal of American Ceramic Society, accepted and published online September 2009.

 

J11. Dagdeviren, C., Papila, M., "Dielectric Properties of Fibrous-ZnO/PVDF Nanocomposites  Polymer Composites, accepted and published online March 2009.

 

J10. Papila, M., Sheplak, M., Cattafesta, L., “Optimization of Clamped Circular Piezoelectric Composite Actuators,” Sensors and Actuators A: Physical, Vol. 147 (1), pp 310-323, September 2008.

 

J9. Yordem, O. S., Papila, M., Menceloglu, Y. Z., “Effects of Electrospinning Parameters on Polyacrylonitrile Nanofiber Diameter: An Investigation by Response Surface Methodology,” Materials & Design Vol. 26 (1) , pp. 33 - 44,  January 2008.

 

J8. Papila, M., Haftka, R. T., Nishida, T. and Sheplak, M., “Piezoresistive microphone design Pareto optimization: tradeoff between sensitivity and noise floor,” Journal of Microelectromechanical Sytems, Vol. 15 (6), pp. 1632 - 1643, December 2006.

 

J7. Goel, T.,  Haftka, R. T., Papila, M. and Shyy, W., “Generalized Pointwise Bias Error Bounds for Response Surface Approximations ,” International Journal for Numerical Methods in Engineering, Vol. 65 (12) , pp. 2035 - 2059, December 2005.

 

J6. Papila, M., Haftka, R. T. and Watson, L. T., “Pointwise Bias Error Bounds and Min-Max Design for Response Surface Approximations,” AIAA Journal, Vol. 43 (8) pp. 1797-1807, August 2005.

J5. Papila, M. and Haftka, R. T., “Implementation of A Crack Propagation Constraint within A Structural Optimization Software,” Journal of International Society for Structural and Multidisciplinary Optimization, Vol. 25 (5-6), pp. 327-338, December 2003

 

J4. Kim, H., Papila, M., Mason, W. H., Haftka, R. T., Watson, L. T. and Grossman, B., “Detection and Repair of Poorly Converged Optimization Runs,” AIAA Journal, Vol. 39 (12) pp. 2242-2249, December 2001

 

J3. Papila, M. and Akgun, M. A., “Post-buckling of Composite I-Sections Part 1: Theory,” Journal of Composite Materials, 35(9), pp. 774-796, 2001

 

J2. Papila, M., Akgun, M. A., Niu, X. and Ifju, P.,” Post-buckling of Composite I-Sections Part 2: Experimental Validation,” Journal of Composite Materials, 35(9), pp. 797-821, 2001

 

J1. Papila, M. and Haftka, R. T., “Response Surface Approximations: Noise, Error Repair, and Modelling Errors,” AIAA Journal, Vol. 38, pp.2336-2343, December 2000

            In Book Chapters

C2. Ifju, P. G., Niu, X. and Papila, M.  “Shadow moire interferometry applied to composite column buckling,” Handbook of Moire Measurement, Edited by C. A. Walker, Holding Publisher, pp. 375-377, February 2004.

 

C1. Kim, H., Mason, W. H., Watson, L. T. Grossman, B., Papila, M. and Haftka, R. T “Protection Against Modeling and Simulation Uncertainties in Design Optimization,” Modeling and Simluation-Based Life Cycle Engineering, Edited by Chong, K. P., Saigal, S., Thynell, S. and Morgan, H. S., Spon Press, pp. 232-244, 2002.